SMC日本品牌2位3通氣控閥，日本SMC氣控閥選型報價
上海乾拓貿易有限公司
企業QQ：
電話；021-69001039
手機；17321017802（微信）
郵箱；17321017802@163.com
地址：上海市嘉定區江橋嘉涌路99弄6號713室
PasConfirm the specifications. Give careful consideration to the operating conditions such as the application,
fluid and environment, and use within the operating ranges specified in this catalog.
2. Fluid 1) Applicable fluid on the list may not be used depending on the operating condition.
Give adequate confirmation, and then determine a model, just because the compatibility list shows the general case.
3. Air quality 1) Use clean air. Do not use compressed air which includes chemicals,
synthetic oils containing organic solvents, salt or corrosive gases, etc.,
適合2種液體涂料 (VCC12D)
?PTFE膜片構造＝替代閥芯滑動部
Do not use the valves in an atmosphere having corrosive gases, chemicals,
as it can cause damage or malfunction. 2) Install air filters. Install air filters close to valves at their upstream side.
A filtration degree of 5 μm or less should be selected. 3) Install an air dryer or after-cooler, etc.
 Compressed air that includes excessive drainage may cause malfunction of valves and other pneumatic equipment.
Water/Chemical base paint, Ink, Cleaning solvent (Water, Butyl acetate), Air
20 to 0.7 (Instantaneous pulsation pressure: 0.9)
?減少涂料的固著
可安裝機器臂 (省空間、輕量)
4. Ambient environment Use within the operable ambient temperature range. Confirm the compatibility between
the product’s composition materials and the ambient atmosphere.
 Be sure that the fluid used does not touch the external surface of the product.
 5. Countermeasures against static electricity
 To prevent this, install an air dryer or after-cooler, etc. 4) If excessive carbon powder is generated, eliminate
 it by installing mist separators at the upstream side of valves. If excessive carbon powder is generated
by the compressor, it may adhere to the inside of the valves and cause a malfunction.
 Refer to Best Pneumatics No.5 for further details on compressed air quality.
Water/Chemical base paint, Ink, Cleaning solvent (Water, Butyl acetate), Air
Not possible (Initial lubricant: White vaseline is used.)
1 or less (3 port valve IN → RETURN: 20 or less) Note 1) 1 or less Note 2)
0 to 1.0 (Instantaneous pulsation pressure: 1.2)
 salt water, water, steam, or where there is direct contact with any of these.
2. Do not use in locations subject to vibration or impact.
3. Do not use in locations where radiated heat will be received from nearby heat sources.
4. Employ suitable protective measures in locations where there is contact with water droplets, oil or welding spatter, etc.
?2閥/1位安裝 (30mm間距)
?2?3通混合安裝
?樹脂集裝塊
2 port 3 port Note 3) 2 port (Diaphragm type)
Poppet seal (PEEK resin + Stainless steel) + Special fluororesin sliding part
Poppet seal (PEEK resin + Stainless steel) + Special fluororesin diaphragm
VCC12 VCC13 VCC12D
Note 1) Supply pressure: Valve leakage at 1.2 MPa (for air) Note
2) Supply pressure: Valve leakage at 0.9 MPa (for air) Note
3) Pressure cannot be applied from a 3 port valve RETURN port.
 Take measures to prevent static electricity since some fluids can cause static electricity.

SMC日本品牌2位3通氣控閥，日本SMC氣控閥選型報價